簡述

Summary

圈圓機是盛產板才圈圓的公用設施配備，為三滾式圈圓機。其布置公正無私、專業調劑便民、盛產合作高、操控簡化，并可在圈圓線程中圈壓出對焊結口處兩直邊，為下一款 工藝程序對焊占領楷模的真正, 基本資料體積尺寸不跨躍4.5mm。This coiler machine is special equipment that is used for steel plate coiling. It has reasonable structure with 3 rollers type design, convenient adjustment, high efficiency and simple operation, and also it can press out straight flange on the two sides of welding joint in the coiling process to lay a good foundation for the next working procedure butt welding except the material exceed 4.5mm.

該防具滿足word打印紙和壓平的兩重的功效。此中word打印紙用作在輪輞板料毛胚上壓出所要的標志，如輪輞的規模、主要參數、主產產家、主產時間等，壓平則是為現階段焊接加工。This is special equipment for rim production, which has dual function of stamping and flattening. The stamper of it is used to press the needed marks on the rim band, including specification, model, manufacturer, production date etc. It flattens weld joint for the following welding operation.

重要性激光加工工藝流程是：拒絕放料à打印機à圈圓à壓平對接焊縫Automatic operating for feeding-stamping-coiling-flattening weld joint

武器頁面布局筒介

Equipment Structure Introduction

磨床由主動的放卷貸款設備、打字貸款設備、卷圓機和壓平貸款設備四位置涉及。The equipment includes four parts：automatically feeder, stamper, coiler and flattening device.

上料功能臺由槽鋼焊接生產而成，上置鋁鋁合金型材上料功能固定支架，用到上料功能積極送進。The feeding platform is welded with structure steel, on which place aluminous feeding rack for material automatically feeding.

縮印機由好壞的兩個印輥子造成，縮印用的字頭裝鄙人輥子，可利用必須很方便的更調。當給料進印輥子內時，鞭策自己印輥子起頭扭動，將鋼字依次印壓在板料上，并將印壓好的板料送來，自后印輥子它是經過了環節液壓泵拒絕規復原位，為了更好地順應時勢卻別板厚的重定向，兩印輥子的間距就可以手工藝慢慢調理。The stamper is made of upper and lower roller. The marking unit is installed on the lower roller, which is easy to change by requirement. When the steel card is feed into the press-stamping roller, push roller to make it roll and stamp steel letters on the band one by one then push out the finished band, the press-stamping roller will back to the home position by the cylinder. The gap between two rollers can be adjusted manually to meet different band thickness.

至關重要指標

Main Parameter

游戲裝備形號	Model Number	Номер модели	JYJ-600-AH
的資料強度	material thickness	Толщина обода	≤4.5mm
鏜孔橫向	Rim Width	Ширина обода	≤320mm
的直徑的規模	Rim Diameter Range	Диаметр обода	300mm~500mm
輸出電壓熱效率	input capacity	Общая мощность	14KW

技藝特征

什么是服務器的電力電氣管理體制由可結構合理器PLC、打戰器、直流軟啟動器、臺達伺服電機管理體制、機械和各種各樣的檢測傳溫度傳感器器組合而成。合理器悅納自己斯耐德開關M218款型，斯耐德開關M218 PLC質量小、數率快、規程化，有串口電訊才會，功能強，靠經得住性強。

This equipment’s electrical system consists of PLC (Programmable Logic Control), contactor, frequency converter, servo system, motor and different kinds of detecting sensor. The controller is used series M218 of Schneider, which is small, fast, reliable, standardizing and has ability of serial communication.

裝備的操縱形式

Equipment’s Operation Mode

主機結構有拒絕和人工帶有大量手動開啟機組兩大類世界任務體例，沿途步驟扳動“拒絕/人工帶有大量手動開啟機組”中斷挑選到。The main machine has two kinds of working mode--- auto and manual, which can choose by turning the “auto/manual” button.

1手動形式

Manual Mode

零丁操作設備法寶的任何服務措施，有利操作審計員的副產物專業調劑和法寶保護。Operate every single action of main machine to make operator easy to adjust and maintain equipment.

2主動形式

Auto Mode

按照具有的法式風格止住被動天道輪回，操作者只要放料、下料機便可。Work circularly and automatically by the set process, the operator only needs to load and unload material.

聯動/單動

single/linkage

電腦主機和及時上料機單位有聯合和單動兩種方式主線任務體例，途經歷程扳動“聯合/單動”消停取舍。There are two working mode for main machine and automatically feeding device--- single and linkage, which can be chosen by turning “linkage/single” button.

單動形式

single mode

在自主的狀態下，唯有網頁打印和卷圓機、壓平機自主的循環，不包括裝料部門。Under the auto mode can only circularly work stamper and flattener without feeding device.

聯動形式

linkage mode

在會去分手后方法下，在彩打和卷圓機會去分手后生死輪回中突顯會去分手后裝料作用，人工主要將料垛放至放卷小車里便可。Under the auto mode, add automatically feeding function to automatical circle of stamping and coiler, worker only need to put material on the feeding dolly.

說話切換

Language

按住“聊天鎖定”后顯現出來右上圖，停機英中文鎖定。Click “language” to get into the interface like above picture, where can choose language between Chinese and English.